James Hardie™ Backing Strip.
A weather seal at horizontal panel joints for use with ExoTec® façade panel and fixing system and Scyon™ Matrix™ cladding.
1,190mm
SAP: 305557
10 per pack
2,390mm
SAP: 305558
10 per pack
2,990mm
SAP: 305559
10 per pack
James Hardie™ Façade Washers
Façade washers used for exposed fastener fixing with ExoTec® façade panel and fixing system and Scyon™ Matrix™ cladding.
SAP:305565
1000 per pack
ExoTec® Top Hat. 6,000mm long.
A rolled metal section, for use with ExoTec® facade panel and fixing system, designed to span across the building structure to support façade panels and isolate differential movement of the panels from those of the structure. 124mm wide x 35mm deep x 1.15mm gauge thick x 6,000mm long.
SAP:304752
45 per pack
James Hardie™ Intermediate Top Hat.
A metal top hat for use with ExoTex® and ComTex® façade panel and fixing system, for intermediate sheet support. 50mm wide x 35mm deep x 1.15mm gauge thick
6,000mm Long
SAP: 302701
50 per pack or 1 each
7,200mm long
SAP:302700
50 per pack or 1 each
ExoTec® Gasket Snap Strip. 3,620mm long.
For use with the ExoTec® façade panel and fixing system, this gasket snap strip is specially designed to clip into the ExoTec® Top Hat at vertical facade panel joins to cover fixings to the structure and to provide an initial weather seal and drainage using a neoprene gasket.
SAP: 305556
10 per pack
James Hardie™ Joint Sealant. 300ml cartridge.
A general purpose, paintable, exterior grade polyurethane joint sealant.
SAP: 305534
20 per box
*Not to be used in impact and/or fire applications.
HardieBlade™ Saw Blade
A 185mm or 254mm diameter poly-diamond blade for fast and clean cutting of James Hardie fibre cement
185mm
SAP: 300660
1 each
254mm
SAP: 303375
1 each
James Hardie base coat
Water resistant jointing system used to flush finish over epoxy when countersinking fasteners.
Required accessory supplied by James Hardie
What is the difference between HardiPanel® Compressed Panel and ExoTec® Facade Panel?
ExoTec® Facade Panel is a new generation engineered fibre composite panel that is sealed all six sides. It has been specifically developed to meet the requirements of commercial facades, with improved stability for a greater range of paint finishes. The ExoTec® Facade Panel has 20% higher impact resistance, requires less fixings, and is faster to paint.
Is the ExoTec® Facade Panel a type of compressed panel?
Yes
Is back coating of the ExoTec® Facade Panel required before installing as a facade?
No, ExoTec® Facade Panel is fully sealed, hence back coating is no longer required.
What happens if ExoTec® Facade Panels are scratched prior to the application of the finishing paint system?
Deep scratches through the coating will not affect the performance of ExoTec® Facade Panel. If panels are scratched through the coating, the face of the panel must be painted according to the coating specification supplied by the selected approved paint manufacturer.
What happens if ExoTec® Facade Panel edges acrylic coated are cut on/off site?
Cut unsealed edges do not affect the performance of ExoTec® Facade Panel provided that cut panel edges are painted as per instructions from the selected approved paint manufacturer.
What is the ExoTec® Facade Panel warranty?
The warranty is 10 years.
Can the back of the ExoTec® Facade Panel be exposed to UV light?
If exposed to direct UV light, then the back of the panel must be protected by either using sarking or applying a pigmented exterior grade paint to the back of ExoTec® Facade Panel.
Why is ExoTec® Facade Panel sealed six sides?
It enhances the panel’s performance by improving the panel’s moisture resistance. It removes the risk associated with an incorrect back sealing product being used.
Can I use the ExoTec® Facade Panel in domestic type construction?
ExoTec® Façade Panel can only be used in domestic construction if the ExoTec Fixing System is used.
Can any other coating system be used other than those tested with the ExoTec® Facade Panel?A. It is the responsibility of the coating manufacturer to ensure the suitability of their coating with the ExoTec® Facade Panel.Back to top
It is the responsibility of the coating manufacturer to ensure the suitability of their coating with the ExoTec® Facade Panel.
What size drill must be used to drill holes for the No 10 countersunk or wafer head screws with the ExoTec® Facade Panel?
A 6mm masonry drill which drills a hole 6.2mm to 6.3mm diameter.
Can ExoTec® Facade Panel be used for applications other than facades?
Specific project requirements can be initially discussed with CustomerLink™ technical team.
